- What volume level should I mix at?
- How important is gain staging?
- What should I set my HPF and LPF to?
- What Hz is best for bass?
- How do you adjust a low pass filter on a subwoofer?
- How do you set a gain structure?
- What should my low pass filter be set to?
- What is gain structure?
- How do you set a gain for singing?
- How does gain work?
- What is a good crossover frequency?
- What should LPF be set on AMP?
- What is proper gain staging?
- What is gain staging in logic?
- Does gain affect sound quality?
- What should subsonic filter be set to?
What volume level should I mix at?
A good rule of thumb is that your volume level should be low enough to allow for conversation without raising your voice.
If you need to shout to be heard, your monitors are too loud..
How important is gain staging?
Gain staging is important because it directly pertains to the volume relationships within our mix. When used effectively, it will avoid increasing the noise floor and keep noise to a minimum. Gain staging will also allow us to maximize the dynamic range of a track while preserving overall headroom in the mix.
What should I set my HPF and LPF to?
You usually set the HPF with a steep slope say 24db/octave because you are trying to protect the sub from damage and a 12-18db/octave on the LPF because you want it to kinda “blend” in with your mids. The steeper the slope (db/octave) the less your sub will creep into the neighboring frequencies.
What Hz is best for bass?
20-120 HzA 20-120 Hz rating is best for bass in most subwoofers. The lower the Hz, the more is the bass you can get. Some of the best subwoofers in the market have this Hz range. If you are buying a subwoofer that has a fixed Hz rating, you should ensure it is lower than 80 Hz if the bass is important to you.
How do you adjust a low pass filter on a subwoofer?
Setting the low-pass filter for the subwoofer output (Subwoofer Low Pass Filter)Select [Setup] – [Audio Settings] from the home menu.Select [Subwoofer Low Pass Filter].Select the setting you want. On: Always activates the low-pass filter with a cutoff frequency of 120 Hz. Off: Does not activate the low-pass filter.
How do you set a gain structure?
To establish proper gain structure, the primary element and first concern is input gain. Each system input provides adjustable Gain In or trim level, with an associated Peak indicator. For best performance, increase the gain on a given input until the Peak indicator just begins to flash on normal signal content.
What should my low pass filter be set to?
As a general rule, the Low-Pass Filter should be set at a value approximately equal to (or below) 70% of your main speaker’s lowest frequency response. For example, your speaker’s frequency response goes down to 43Hz. 70% of 43Hz equals 30.1, so you should set the subwoofer’s low pass filter to 30Hz.
What is gain structure?
The concept of gain structure is that, at each connection between components in the system, the signal level is as high as it can be (to minimize noise), but no higher than the maximum level that either component allows (so there is no distortion due to overload).
How do you set a gain for singing?
The first method of gain setting follows the studio mentality and says the fader should start at the infinity position (at the bottom) and the gain is increased until the input meter reads almost to the red while allowing for signal increases without distorting, such as when a vocalist sing a lot louder for a passage …
How does gain work?
Your gain setting determines how hard you’re driving the preamp section of your amp. Setting the gain control sets the level of distortion in your tone, regardless of how loud the final volume is set.
What is a good crossover frequency?
What is the recommended crossover frequency for a subwoofer? For THX Certified and non THX Certified home theater systems, 80 Hz is the recommended setting. However, you can set the crossover (LPF) between 80 Hz – 120 Hz based on which setting sounds best for your system.
What should LPF be set on AMP?
With only one amp receiving signal from your head unit, play your favorite type of music at about 75% volume with the LPF filter on your amp set as high as it will go. Slowly turn the dial from high to low until you stop hearing all the high frequencies through your subwoofers.
What is proper gain staging?
Gain staging, or gain structuring, is the act of setting the gain for each amplification stage (gain stage) in a sound system to achieve a target system volume that minimizes noise and distortion. Said another way, proper gain staging allows your sound system to achieve the best signal-to-noise ratio.
What is gain staging in logic?
What is gain staging? Gain staging is level management. It comes from the analogue days where it was essential to get a good signal-to-noise ratio whilst preventing clipping the channel. … Gain staging was also very necessary to make sure that the level going into each hardware unit was optimal.
Does gain affect sound quality?
To recap, volume is a control of the loudness at the output of a sound system and has no affect on quality, while gain lets you increase the loudness inside of an audio system, which absolutely determines the quality of the sound or recording.
What should subsonic filter be set to?
Since the Hz setting on the subsonic filter is the start of a slope, not a cutoff, we want to set it higher than 20 Hz. The sweet spot for getting some pounding bass without destroying your subwoofer is between 25 Hz and 35 Hz.