Quick Answer: Is It OK To Use 0w20 Instead Of 5w30?

Is 0w 20 oil too thin?

At the normal operation temperature, SAE 0W-20 is not very much “Thinner” than SAE 5W-30, although the latter MAY provide marginally more protection when the engine is hot, the much higher viscosity when cold will lead to excess wear, hard starting and higher fuel consumption.

It may also void the warranty..

What is the difference between 0w20 and 0w30 oil?

The 0w20 motor oil when compared to the 0w30 happens to have a lower viscosity, thus, making it a little less thick than the former. Temperature range; when compared, the 0w20 motor oil happens to have a higher temperature than the 0w30 motor oil. … Also, it can be used for engines that 5w20 is recommended.

Why does Toyota use 0w20 oil?

Why does Toyota recommend 0w-20 synthetic oil for their engines? … That is because the oil’s viscosity will thicken as it warms up. Thicker oil protects better than thinner oil, in general, but it can’t protect if it doesn’t flow. Thinner oil flows easier but doesn’t protect as well.

Is Thicker oil better for older engines?

A: Yes. This is a practical method to improve oil pressure in an older, high-mileage engine. The slightly thicker oil film from the heavier base weight oil — 10W — can help protect worn engine bearings as well.

How long does 0w20 synthetic oil last?

A: Yes! The superior qualities of synthetic oil have allowed the oil change interval to be extended from 5,000 miles to 10,000 miles. However, an owner should continue to check the oil level regularly and top-off if needed.

Is 0w20 better than 5w30?

It readily means that the 0 oil will flow well and better at a cold temperature more than 5W-30 oils even while maintaining the same viscosity. … Temperatures and certain climate conditions affect the use of 0W-20 over the 5W-30 engine oil.

What happens if I put 5w30 instead of 0w20?

In winter it will be fine but in summer the viscosity will be thinner in high temperatures. The engine will survive but there may be long term damage. … 5w30 can be fully synthetic, however, putting it into your engine which is designed for 0w20 is a bad idea. If it isn’t on the fill cap don’t put it in your engine.

Does it matter if you put 10w30 instead of 5w30?

Most oils will mix perfectly, provided they have a similar synthetic. Therefore, there is no problem in mixing 10w30 and 5w30 since one will be topping up. Mixing the viscosity of oils will not have any effect on the engine. 5w30 and 10w30 engine oils have close viscosity, and thus there is no harm in mixing them.

Is mixing 5w30 with 10w30 bad?

Yes, if topping up. If your oil must be topped up, then you are burning oil already, so the difference won’t cause more damage than is already there. 5W30 and 10W30 are essentially the same at operating temperature.

Can I switch from 5w30 to 0w20?

0W20 and 5W30 are very interchangeable in our cars. You can use any and your car will run fine and will not void any warranty for those of you under warranty. After your warranty is over, I am sure 5w30 maybe the better oil to use over 0w20.

Will 5w20 hurt a 0w20 engine?

Sure, 0W20 will flow better than 5W20 at low temperatures, but the difference is minimal and both versions run thin in cold conditions. However, if you live in an extremely cold region, the 0W oil will do less damage than the 5W oil while starting the engine.

What happens if I use the wrong oil?

You might notice a few oil spot in your garage or under your car because using the wrong oil can lead to leaks, or you might become aware of a burning smell while driving. If the oil isn’t working as it should engine parts might not be lubricated well enough and cause friction, which can burn the oil.

What happens if I put 10w40 instead of 5w30?

If you use 10-w-40 instead of 5-w-30 specified by the manufacturer then the viscosity of 10-w-40 used by you will be higher and oil thicker than what is specified during winters. Similarly the oil viscosity will be higher and oil thicker than specified during summers.

Should I use thicker oil in a high mileage engine?

A: Yes. This is a practical method to improve oil pressure in an older, high-mileage engine. The slightly thicker oil film from the heavier base weight oil – 10W – can help protect worn engine bearings as well.

What does 0w 20 mean?

Breaking down the 0W-20 code, “0” is the oil’s viscosity at startup when the engine is cold, “W” stands for its winter certification, and “20” is the viscosity at higher temperatures. Lower numbers designate thinner, lower-friction oil.